Woodworking DIY

10 Common Wood Turning Mistakes

Woodworking Plans Banner




Short article: http://ycmt2.com/blog/lathe-mistakes

Wood turning at the lathe is a really satisfying craft where you can make cool things FAST! But like all skills and crafts, there are several typical errors to fall under that can make the experience aggravating. Here I cover the primary ones I know.

VIDEOS REFERENCED:
Carl Jacobson Woodturning Basics Playlist: https://www.youtube.com/playlist?list=PL3NhpJNKou8DRKScGXu2j9vq0gSDGTI_e

MY TOOLS
https://ycmt2.com/tools-i-use

MUSIC CREDIT
Epidemicsound.com and AmpleTunes.com
#woodturning #woodworking #woodlathe

TOOL GIVEAWAYS
On a monthly basis on Patreon I have a contest that just requires you to respond to a concern I publish. Clients at all levels are eligible, however higher levels have more benefits! Join the contest at: www.patreon.com/YouCanMakeThisToo

SOCIAL MEDIA
Patreon: https://www.patreon.com/YouCanMakeThisToo
Facebook: https://www.facebook.com/YouCanMakeThisToo/
Instagram: https://www.instagram.com/youcanmakethistoo/

MISTAKE 1: NOT SANDING WITH THE GRAIN

Sanding on the lathe is pretty simple since you can just switch on the lathe and hold sand paper against it while it turns. The issue is your most likely sanding across the grain, which makes the scratches incredibly visible. Luckily, remedying this is actually basic. Prior to moving to the next grit, stop the lathe and sand along the piece to erase those scratches. We’re really just changing the instructions of the scratches, but so long as they’re choosing the grain our eyes don’t actually notice them.

ERROR 2: PRACTICING ON SOFT WOOD

Its tempting to practice on soft wood due to the fact that it’s less expensive, however it’s softness makes it actually tough to turn adequately. A great tool finish needs very sharp tools and near ideal method. Personally, among my favorites to turn is maple. It’s a difficult sufficient to turn well, closed cell, pretty economical, and easy to discover on the roadway side!

ERROR 3: FOCUSING ON THE WRONG SIZE

It’s easy to get covered up on bed length. Unless you KNOW you’re going to be turning long stuff, chances are you’re going to lack swing (range between the bed and center – how thick a blank you can turn) a lot earlier. Pay more attention to the swing than bed length.

ERROR 4: TURNING AT THE WRONG SPEED

Large, unbalanced, or rough things do better turned at slower speeds. Going too fast prematurely can be devastating. As soon as you get down to final passes though, cranking up the speed can help get a best tool surface that doesn’t need sanding.

MISTAKE 5: TURNING WITH DULL TOOLS

Sharpening isn’t fun, and it’s even less enjoyable when you’re not great at it. Know what’s even less enjoyable than honing? Attempting to turn with dull tools. It just doesn’t work. The finish will not be good, there’ll be more remove, and a greater opportunity of catches. Just take the time to hone, and the more you do it the much better you’ll get!

MISTAKE 6: NOT RE-TIGHTENING THE CHUCK

Once it’s good, I tighten the chuck again and it’s always unexpected how simple it moves after that brief spin. The apparent safety factors, that 2nd tightening is also going to result in better turnings by keeping the piece steadier.

ERROR 7: NOT WEIGHING DOWN THE LATHE

Mini and midi lathes aren’t heavy or extremely huge, so they require to be attached to something that is to keep those vibrations down. Turning is challenging enough without your workpiece and tool shaking around.

MISTAKE 8: NOT WEARING PPE

Turning at a lathe includes spinning a hard piece of material at a high rate of speed towards your face. Preferably an effect ranked face shield ought to be used while turning, and a good dust mask. Be sure nothing loose or dangly clothing is close to the lathe, it can get sucked in and pull you into the lathe.

MISTAKE 9: NOT REPOSITIONING THE TOOL REST

Getting your tool rest at the right height and distance from the piece is extremely important. And is different for traditional tools and carbide tools, and if you change tools, you might need to change the rest.

MISTAKE 10: FORGETTING THE OTHER EXPENSES

Wood turning at the lathe is a very gratifying craft where you can make cool things FAST! Sanding on the lathe is quite simple since you can just turn on the lathe and hold sand paper versus it while it turns. Unless you KNOW you’re going to be turning long stuff, odds are you’re going to run out of swing (range between the bed and center – how thick a blank you can turn) a lot quicker. Trying to turn with dull tools. Turning is challenging enough without your workpiece and tool shaking around.

A lathe is a fairly economical tool, however you’ll likewise need tools, a method to hone those tools, work holding devices, other tool rests, hardware/kits to turn, wood. it can build up.

Leave a Reply

Your email address will not be published. Required fields are marked *

TedsWoodworking Plans and Projects